AC repair
Furnace & heating
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateFast, Reliable Furnace Repair Across Dallas
When your heat quits in the middle of a Dallas cold snap, you want a straight answer and a working furnace, not a sales pitch. We work on gas furnaces and heat pumps across Dallas, from the older pier-and-beam homes near Deep Ellum to the postwar brick houses of East Dallas. Dallas winters are short but they hit hard, and a furnace that limped through last season usually picks the coldest week to fail. Our technicians have up to 12 years of experience and know the brands inside these homes before they arrive.
Call (866) 942-9965. We answer 24/7, and we run fast dispatch from 7am to 7pm, Sunday through Friday. Estimates are free.
Why Dallas Homeowners Call Stallion AC Repair for Furnace Repair
Dallas HVAC work is its own animal. This city swings from 100°F-plus summers to genuine freezes, and a furnace here has to do its job while the same house is built for peak cooling load. That mismatch is where a lot of our calls come from, and it’s why we ask about the whole system, not just the broken part.
We handle both heating and cooling, so you’re not juggling one contractor for the furnace and another for the AC. When the honest answer is “replace it” or “this older system needs rightsizing before another repair makes sense,” we say so plainly. When it’s a capacitor or a blower motor, we tell you that too. Repair-or-replace advice shouldn’t depend on which option pays better.
Our technicians are trained across nine leading brands, so the diagnosis starts with knowledge of your specific equipment rather than guesswork. That shortens calls and it keeps you from paying for trial and error. Whether you’re near Uptown or out toward the core, we serve Dallas and the surrounding neighborhoods, and we book work around the same weather the whole city is dealing with.
Styles & brands we work with
- AC repair
- Furnace & heating
- Heat pumps
- Ductless mini splits
- Carrier
- Trane
- Goodman
Heat Pump Repair in Dallas
Heat Pump Repair in Dallas often comes down to the extremes: a system sized for brutal summer heat that gets asked to produce warmth during a hard freeze. Heat pumps here run year-round, so by the time winter arrives the reversing valve, defrost controls, and refrigerant charge have already been through a full cooling season. When a Dallas homeowner calls, it’s usually because the unit is blowing cold in heat mode, icing over, or tripping the breaker after a storm. Typical heat pump repair runs $150 – $700, and the written estimate sets the final price.
Reversing Valve and Defrost Troubles
A heat pump stuck in cooling mode or icing up in cold weather usually points to the reversing valve or a defrost control that’s failed. These are diagnosis-first jobs. A technician tests the valve and the board before quoting a repair, because replacing the wrong part wastes your money.
Storm and Surge Checks
Spring thunderstorms and grid switching knock out control boards and capacitors on outdoor units. After a surge, the system may run but cycle wrong, or not start at all. Testing the board and capacitor before restarting anything prevents a small fix from becoming a compressor replacement.
Heating Repair in Dallas
Heating Repair in Dallas spikes after the kind of hard freeze that burst pipes and killed condensate lines across East Dallas and Deep Ellum in 2021. Many of those same older homes now need freeze-protection upgrades alongside the repair itself, a pattern you rarely see in newer suburban housing. When a furnace won’t light, short-cycles, or trips the breaker, we trace it from the ignitor and gas valve through the blower and heat exchanger. Typical heating repair runs $150 – $700, with the written estimate setting the final cost.
Freeze-Protection Upgrades
After a deep freeze, the repair is only half the job. Older homes on pier-and-beam foundations around the core often need condensate lines rerouted or insulated and freeze protection added so the next hard freeze doesn’t repeat the damage. We tie that work into the heating call so it gets done in one visit.
Ignitor, Gas Valve, and Blower Motor
Most no-heat calls land on an ignitor, a gas valve, or a blower motor that’s been cooked by years of extreme attic heat. Gas-related work on these parts needs a trained technician. We test and replace rather than talk you through it, because a gas valve isn’t a homeowner repair.
Trusted Brands We Service in Dallas
We work on Goodman, Rheem, York, and Daikin equipment, plus Carrier, Trane, Lennox, Bryant, and American Standard. That covers the value-tier furnaces common in Dallas’s older homes and the premium systems going into newer builds. We don’t claim to keep parts in stock, so what we offer is straightforward: a technician who knows the brand, an accurate diagnosis, and a fast turnaround on getting you heat. If a part needs ordering, we tell you the timeline up front instead of leaving you guessing through a cold night.
See the difference
Before
After
Before
After
Before
AfterCommon Furnace Repair Problems We See in Dallas Homes
- Flooded condenser coil after heavy rain or ice melt. In the older inner-ring neighborhoods, a submerged outdoor unit is common after a storm. Flipping the breaker on a wet condenser can short the compressor, so it has to be dried and tested first.
- Power-surge damage to control boards and capacitors. Dallas’s spring thunderstorm season and grid switching take out boards and capacitors across the city. These show up as a system that won’t start or cycles erratically.
- Weak capacitors and seized blower motors. In pier-and-beam homes, attic heat is extreme and it accelerates wear on capacitors and blower motors. It’s often the first thing to fail in a system pushed past its design limits.
- Undersized systems and restricted airflow. Many older homes still have original galvanized ductwork and undersized returns hiding in crawlspaces. When airflow is restricted, a simple repair can turn into a duct redesign.
Pricing for Furnace Repair in Dallas, TX
A typical furnace repair in Dallas runs $150 – $700. That range covers the common failures: ignitors, capacitors, blower motors, gas valves, and heat exchanger work. What pushes a job toward the top of the range is anything that turns into more than a part swap, like a blower motor on a system that’s been overheating for years, or duct restriction that has to be corrected for the furnace to run right. After a freeze or a flood, add the drying and testing time that has to happen before anything gets restarted.
| Service | Typical Estimated Range |
|---|---|
| Furnace Repair | $150 – $700 |
| Heat Pump Repair | $150 – $700 |
| Heating Repair | $150 – $700 |
The written estimate sets the final price. Estimates are free. Call (866) 942-9965 and we’ll get a technician out to look.
We Also Serve Cities Near Dallas
If you’re just outside the city, our furnace repair team covers the surrounding area too. We also take calls in Mesquite, Irving, Garland, and Richardson. Same straight talk, same upfront estimate, same free consultation before any work starts. If you’re in one of those cities and your furnace is failing, call and we’ll tell you what we can do and when.
Serving Dallas, TX – Our Local Coverage Area
We serve Dallas and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Furnace Repair in Dallas
Check for water or ice anywhere near the furnace and outdoor unit before you restore power, and if you find any, don’t turn it on. In older pier-and-beam homes around Deep Ellum and East Dallas, burst pipes and killed condensate lines were widespread that year, and restarting a wet unit can cause electrical damage. Have a technician inspect it dry first.
No. A flooded condenser must never simply be switched back on. A submerged coil that’s restarted wet can short the compressor, and that turns a small repair into a full replacement. The coil has to be dried and tested before power comes back. If you’re not sure it’s dry, call (866) 942-9965 and we’ll check it.
Because those pier-and-beam houses often hide original galvanized ductwork and undersized returns in the crawlspaces. When airflow is restricted, a furnace repair can turn into a duct redesign. A technician checks static pressure and inspects the runs so the fix actually solves the problem instead of masking it.
Yes. Spring thunderstorms and grid switching in Dallas routinely damage control boards and capacitors, which shows up as a unit that won’t start or cycles wrong. Testing the board and capacitor after a storm is cheaper than replacing a compressor later. Call for an estimate if you suspect surge damage.
Run it from a generator sized for the starting load, and let the system pull from a properly installed surge protector rather than restarting it repeatedly on unstable grid power. Repeated hard starts wear the compressor. A technician can check freeze protection and surge setup before the next cold snap.
When your heat goes out in Dallas, call (866) 942-9965 for a free estimate. We answer 24/7, and we run fast dispatch from 7am to 7pm, Sunday through Friday. One contractor for your furnace, your AC, and everything in between.
Written by the team at Stallion AC Repair.